Last edited by a moderator:
OTRATTW Switches
- Thread starter Muadeeb
- Start date
FaroutX
Bought an X
- Location
- Sparks, NV
^^I need two more otrattw switches for a clean match also, very easy to wire up, I tapped off the hazards!
Last edited:
- Location
- SW OK & formerly Eastern NM
A write up on the whole process of writing up an OTTRAW switch would be much appreciated!
FaroutX
Bought an X
- Location
- Sparks, NV
Update, just recieved an email, my lights are gonna be here next week!:excitement:
I'll start working on a write up while the lights are being shipped. I will have order The Otrattw switches needed also, might take a couple weeks to find time to do the install and How-To!:distracted:
I'll start working on a write up while the lights are being shipped. I will have order The Otrattw switches needed also, might take a couple weeks to find time to do the install and How-To!:distracted:
- Location
- Idaho!
^Which switches are you getting? I forgot which ones I ordered last year for my other roof lights. I'm wondering on the exact diff btwn these two (other than what I'm reading, which I understand as gobbledegook:
1.)
Product ID: V1D1J66B-AYCZL-1ZL
Manufacturer: Carling Technologies
V-Series Contura II sealed rocker switch, ZOMBIE Lights
Details
SPST ON/OFF switch
Black hard surface rocker,BLUE lens.
Two incandescent lights.
The Upper light is ON when the upper part of the rocker is pressed (ON).
The lower light is independently wired
This switch uses the same light configuration as the ARB switches.
V1D1J66B is rated 20A @ 12V.
V1C1J77B is rated 20A @ 18V.
No rear barriers in the back between terminals. VCH connector housiings can be used
2.)
Product ID: V1DAF76B-AYCZL-1ZL
Manufacturer: Carling Technologies
Contura II Sealed rocker switch, ZOMBIE Lights
Details
SPST ON/OFF switch.
Black hard surface rocker, BLUE lens
Two incandescent lights.
V1DAF76B has a 18 volt upper independently wired light (the 18 volt incandescent light will produce about 1/3 less light than a standard 12 volt incandescent light when used in a 12 volt circuit). Separate grounds for the internal switch lights Rear barriers between the terminals.
V1D1G66B has a 12 volt upper independently wired light. Common ground for the lights in the switch. No rear barriers
The V1DAF and V1D1G have a 12 volt lower light that is ON when the switch is turned ON.
Rated 20A @12V.
1.)
Product ID: V1D1J66B-AYCZL-1ZL
Manufacturer: Carling Technologies
V-Series Contura II sealed rocker switch, ZOMBIE Lights
Details
SPST ON/OFF switch
Black hard surface rocker,BLUE lens.
Two incandescent lights.
The Upper light is ON when the upper part of the rocker is pressed (ON).
The lower light is independently wired
This switch uses the same light configuration as the ARB switches.
V1D1J66B is rated 20A @ 12V.
V1C1J77B is rated 20A @ 18V.
No rear barriers in the back between terminals. VCH connector housiings can be used
2.)
Product ID: V1DAF76B-AYCZL-1ZL
Manufacturer: Carling Technologies
Contura II Sealed rocker switch, ZOMBIE Lights
Details
SPST ON/OFF switch.
Black hard surface rocker, BLUE lens
Two incandescent lights.
V1DAF76B has a 18 volt upper independently wired light (the 18 volt incandescent light will produce about 1/3 less light than a standard 12 volt incandescent light when used in a 12 volt circuit). Separate grounds for the internal switch lights Rear barriers between the terminals.
V1D1G66B has a 12 volt upper independently wired light. Common ground for the lights in the switch. No rear barriers
The V1DAF and V1D1G have a 12 volt lower light that is ON when the switch is turned ON.
Rated 20A @12V.
Mel, here's the diagrams for your switches
The one on the left is the #1, and right is #2. Your 2nd switch also has a set of barriers between the terminals so you could use standard 1/4" push on terminals (female) instead of ones that are 100% insulated.
The one on the left is the #1, and right is #2. Your 2nd switch also has a set of barriers between the terminals so you could use standard 1/4" push on terminals (female) instead of ones that are 100% insulated.
FaroutX
Bought an X
- Location
- Sparks, NV
^^ I'm have Jim make me some custom L.E.D. switches, the logos look like dullys, he is going to try and squeez 4 logos on one switch for my roof lights and change some of the text on the switches, they are all off/on switches Amber on top and SB Red on bottom bar which is lit when lights are on except for my top roof light switch is a off/on/on, it will turn on the first set of roof lights on with the first on, then the second on turns all the lights on! Hope that makes sense! I will post a How-to with pics!
The difference between the switches above is the light config, one is lit on top when switched on and the other is lit on bottom when switch on, it's hard to tell other that, call Jim at Otrattw and he can go into more detail, he is very helpful!
The difference between the switches above is the light config, one is lit on top when switched on and the other is lit on bottom when switch on, it's hard to tell other that, call Jim at Otrattw and he can go into more detail, he is very helpful!
- Location
- Smyrna, TN
MMMMMM Switch pron. Love it. I'm tagging this one for later use.
- Location
- Winlsow Twsp, NJ
The Switch guys are awesome! I asked on their facebook for some pink LEDs and they got some and are going to start producing them! I can't wait to buy some!
- Location
- Idaho!
I think my coworkers may either be offended or find that hilarious if i have a bacon switch, haha!
Thanks Farout for the clarification!
Thanks Farout for the clarification!
FaroutX
Bought an X
- Location
- Sparks, NV
Jim at Otrattw just sent me the prototype switch symbol design:
Top pic symbols will be for my front Dully D2's and for my new SRM2's side lights I will use the symbols in this bottom pic:
Should have them next week!
Top pic symbols will be for my front Dully D2's and for my new SRM2's side lights I will use the symbols in this bottom pic:
Should have them next week!
FaroutX
Bought an X
- Location
- Sparks, NV
I'm changing the two covers on my front and rear roof lights to this new style, $5 for each cover! My front 4 dually d2's will use the off/on/on switch to control both sets on one switch!
oh thats awesome! should have thought of something like that
TN4x4Xterra
Suspension Lift
- Location
- Knoxville, TN
I have 4 of these switches from Jim....awesome quality and easy to deal with!
TN4x4Xterra
Suspension Lift
- Location
- Knoxville, TN
How's that you got them today? Mail, fedex, ups don't deliver on Sunday's....
- Location
- Conroe, TX
Now if we could get this guy involved more on XN
Already in talks with the dude. Last I heard, he needed to see where his budget was at the end of the year.
FaroutX
Bought an X
- Location
- Sparks, NV
Just recieved this email with pics, my switches are ready and on the way:
- Location
- New Mexico
Just recieved this email with pics, my switches are ready and on the way:
I was thinking about using the regular stock, alley light switch covers for my SRM2 side lights. How much did it cost for the custom graphics on those?
-Rok
FaroutX
Bought an X
- Location
- Sparks, NV
^^^Zero, just all Jim, he's cool, tell him what you want, he is also very patient and explains everything, diffently know his stuff! The covers are just $5, and easy to change, you can mix and match at that price!
- Location
- Smyrna, TN
Bump for selfish reasons.
- Location
- Signal Mtn., TN
I've got one for rock lights and one for apocalypse lights (LED bar) ordered and on the way.
- Location
- Smyrna, TN
I think 3 switches constitutes the need for a switch panel/box, yes?
- Location
- Signal Mtn., TN
That seems perfectly reasonable to me.
- Location
- Smyrna, TN
I thought so. Rear LEDs (Hanmas), front 7" bar, and Rock lights to start...
- Location
- Brentwood, TN
OTRATTW makes a 3, and 6 switch frame that you can install switches into. Carla I have an extra 3-bank switch if you are interested.
- Location
- Conroe, TX
Put in another request :-D
Sent Using Tapatalk 4
from a Galaxy SIII
FAR, FAR AWAY
Sent Using Tapatalk 4
from a Galaxy SIII
FAR, FAR AWAY
- Location
- Ontario Canada
They also have the single ones that can be connected together to make how ever many switches in a row you would like
- Location
- Smyrna, TN
- Location
- Brentwood, TN
PM sent w/ parts list.