- Location
- Hainesville IL
The Greater Post Whore Society - Volume 5: New Blood
- Thread starter Prime
- Start date
- Status
- Location
- Hainesville IL
Cooky8
Test Drive
Hello motherufckers! I got a simple question and it's easier and quicker to ask it here since you all love this place
I need to Jack up my 1th gen x to out it in stands for bodywork and changing the shocks. Where do I lift it, where is the safest place for stands?
Picture for attention
I need to Jack up my 1th gen x to out it in stands for bodywork and changing the shocks. Where do I lift it, where is the safest place for stands? Picture for attention
Attachments
- Location
- Denver Adjacent
I like you.Hello motherufckers! I got a simple question and it's easier and quicker to ask it here since you all love this place
Picture for attention
Jack it at the lower control arm mounts. Place jackstands along the frame rails at the front.
Lift rear by Differential. If you're changing the rear shocks you'll again want to put stands on the frame so the axle can droop.
- Location
- Hainesville IL
coffee.
i get to pick up and axle soon.
i get to pick up and axle soon.
Cooky8
Test Drive
- Location
- Long Island NY
- Location
- Long Island NY
Nvm pulled the tail light lol
- Location
- Denver Adjacent
I have the 1st gen FSM laying around here somewhere.
- Location
- Ontario Canada
best headlight bulbs for the stock headlight housing. not able to do a HID retrofit ( no time before winter shows up). and the Philips Xtreme vision bulbs suck the big one.
also I understand that LED fog lights don't creat enough heat to melt snow but are there any other dowsides of using LED lights as a fog light
also I understand that LED fog lights don't creat enough heat to melt snow but are there any other dowsides of using LED lights as a fog light
- Location
- Denver Adjacent
Tay-Lo
I'm the king of junk food!
- Location
- Upstate SC
Got some small connectors to make an extension for my solar generator panels. What came with the kit was just to short to have the panels outside and the battery pack where its usable inside so I added 30ft to it.
- Location
- Ontario Canada
Well ordered those light bulbs. Hope they are better then the ones I picked up earlier this summer. Also picked up some LED fog lights with the amber signal in the centre similar to joe my reverse light pods
- Location
- Long Island NY
Took one of the tail lights out screws were behind the bedliner.
Brown/red- running lights
blue/red- tail lights
green/red- right turn signal
green/yellow- left turn singnal
yellow/red- reverse lights
black- ground.
But now I ran into the issue of trailers are wired for 4 pin (running, left, right, and ground)
I need it to basically be a 5 pin since the turns and stops are individual on the 1st gens (running,, stop, left, right, and ground)
- Location
- Denver Adjacent
Linky?
- Location
- Ontario Canada
Liteway Customized 3.5" Pair 48W CREE LED Light Bar Turn Signal Amber Pods Light Round Flood Beam Driving Lamp Working Light Waterproof IP68 Fog Lights for Jeep Offroad Truck Car ATV SUV Marine Boat,1 Year Warranty
jsexton
Need Bigger Tires
- Location
- Lewis Center, OH
- Location
- All over PA
- Location
- All over PA
Jesus. Chris collingsworth’s voice is like nails on a ufcking chalk board to me.
- Location
- Denver Adjacent
How are you going to mount those?
- Location
- Denver Adjacent
Yeah. It'd require a custom 7-pin setup to get all the lights working correctly.
- Location
- Denver Adjacent
You could also do a dual 4 pin. Leave the stock 4 pin for brake lights and ground. Add a second 4 pin for reverse lights and turn signals.
- Location
- Ontario Canada
planning on replacing the PIAA lights in the bumper. they should mount the exact same way as the PIAA
- Location
- Denver Adjacent
Scratch that. Don't touch the stock trailer wiring. Add a custom 5 pin for the frontrailer. Ground, stop, reverse, left, right.
- Location
- Denver Adjacent
That way you still have the stock harness if you have to tow some other trailer. But the custom 5 pin for the frontrailer.
- Location
- Denver Adjacent
Word. Didn't know that your bumper used stud mount fogs.planning on replacing the PIAA lights in the bumper. they should mount the exact same way as the PIAA
- Location
- Hainesville IL
mmmm meatball and veggie stew
- Location
- Hainesville IL
also this
- Location
- Long Island NY
Found an actual converter that separates the signals.
- Location
- Denver Adjacent
Oh yeah? Curious. Linky?
- Location
- Hainesville IL
bumper cookies.
- Location
- Long Island NY
- Location
- Hainesville IL
on tonights episode of cursed youtoob recommendations.....
kryter
First Fill-Up (of many)
- Location
- Aurora Colorado
10 hours of electrical code class sat and 10 on Sunday I'm on the 3rd pitcher of margaritas replacing the spark plugs on the 05 tomorrow should be fun cheers bitches
- Location
- Hainesville IL
randomly looking at D44 diff covers. came across this odd one. i like it.
https://www.alienmachineworx.com/product/dana-44-differential-cover/
https://www.alienmachineworx.com/product/dana-44-differential-cover/
- Location
- Hainesville IL
- Location
- Hainesville IL
- Location
- Long Island NY
Just stick with ruff stuff well with it
- Location
- Long Island NY
morning peeps
- Status