- Location
- Greenville SC
I'm copying and pasting from another forum. If you guys have any questions about the car or want more details hit me up.
I don't have the time for a project car anymore and its been slow going to finish it up to my level of detail so I'm looking to sell this move to something newer. I'll keep working on finishing it as long as I have it (and the price will go up if that happens) and I'm not going to take any lowballs. Looking for $8000
To get it running it needs the following finished up: Fuel lines finished, power steering lines finished, wiring harness/ecu/nistune board installed and an exhaust made.
1996 S14 240SX SE, I'd estimate chassis mileage around 175k but I honestly have no clue, cluster has been changed numerous times before I even got the car 11 years ago. Chassis was originally auto and has been through 4 drivetrain swaps (KA, RB, SR, VH) I bought it with the SR and cleaned up the auto-manual stuff (new pedals) Chassis does have broken subframe stud, I have a replacement and was going to borrow a lift to replace it. I drove on it for 4+ years with it broken.
Exterior:
Genuine Nismo FRP front bumper
Navan grill
Kouki sideskirts and tail lights
German glass headlights
Enkei RPF-1 17x9 and 17x10 (have 1 spare of each size as well)
Body is very straight and clean, very few dings, no rust.
machined 450SX badge on trunk lid
Hood is stock with the underside cut out and PBM hood spacers.
Interior:
Driver seat is a Recaro SR-3 wtih Le Mans pattern (confetti)
Rest of the seats are OEM leather, kinda rough shape
Rest of the interior is in pretty good shape
OEM German (?) 260 km/h gauge cluster
Alpine Head Unit, Type R components front coax rear circa 2010.
Greddy MSS as a fan controller
Engine/Drivetrain/Engine Bay
1994 VH45DE with ~88k miles; replaced every gasket and seal from the OEM full gasket set except the head gaskets
Many exterior engine parts/brackets replaced or repainted.
Full Mazworx VH45 to S-chassis swap kit including intake and headers
Xcessive Engineering alternator bracket
B14 brake booster (smaller diameter)
Touge Factory SR20 Pulley set (water pump, alternator, PS)
Most visible bolts replaced with SS cap screw or button heads or new OEM.
Nickel plated OEM fuel rails
All new OEM vacuum and breather lines under plenum (All of the complex formed lines if you know the VH45 at all)
Wiring specialties S14-VH45 Pro harness (not installed)
S1 ECU and Nistune Daughter board (not installed)
1991 Z32 TT transmission with ~60k miles with all outer seals/parts refreshed
Z1 Motorsports "Mild Performance" clutch kit
Z1 Motorsports 11 LB flywheel
Z1 Motorsports Short Shifter
Xcessive Engineering shifter bracket
Mazworx/PST aluminum driveshaft
S15 Helical LSD
Sard FPR and gauge
Fuel Lab billet fuel filter
All fuel lines are aeroquip startlite
Billion universal PS reservoir
Earls cooler for PS
All PS lines are aeroquip AQP high pressure
Griffin radiator custom made for me - S14 Chassis with VH45 hose outlets, i'm using both OEM radiator hoses)
FAL S14 bolt on radiator fans
Sard catch can
Generic CF cooling panel
Chassis/Brake/Suspension
R33 GTS-T front Calipers with OEM Nissan rotors
I have the 75% of the stuff for R33/Z32 rear brake swap (not installed)
Z32 rear uprights (not installed)
SPL brake lines
Yashio Factory core support braces
Supernow billet sway bar brackets (for the OEM bars)
Progress Group sway bars (no brackets or endlinks)
Tanabe tension rods with highest spec Aurora rod ends
Nismo power brace
Nismo front/rear strut tower bars (front not installed for the obvious reason)
SPL diff and subframe bushings GEN 1 (not installed)
I don't have the time for a project car anymore and its been slow going to finish it up to my level of detail so I'm looking to sell this move to something newer. I'll keep working on finishing it as long as I have it (and the price will go up if that happens) and I'm not going to take any lowballs. Looking for $8000
To get it running it needs the following finished up: Fuel lines finished, power steering lines finished, wiring harness/ecu/nistune board installed and an exhaust made.
1996 S14 240SX SE, I'd estimate chassis mileage around 175k but I honestly have no clue, cluster has been changed numerous times before I even got the car 11 years ago. Chassis was originally auto and has been through 4 drivetrain swaps (KA, RB, SR, VH) I bought it with the SR and cleaned up the auto-manual stuff (new pedals) Chassis does have broken subframe stud, I have a replacement and was going to borrow a lift to replace it. I drove on it for 4+ years with it broken.
Exterior:
Genuine Nismo FRP front bumper
Navan grill
Kouki sideskirts and tail lights
German glass headlights
Enkei RPF-1 17x9 and 17x10 (have 1 spare of each size as well)
Body is very straight and clean, very few dings, no rust.
machined 450SX badge on trunk lid
Hood is stock with the underside cut out and PBM hood spacers.
Interior:
Driver seat is a Recaro SR-3 wtih Le Mans pattern (confetti)
Rest of the seats are OEM leather, kinda rough shape
Rest of the interior is in pretty good shape
OEM German (?) 260 km/h gauge cluster
Alpine Head Unit, Type R components front coax rear circa 2010.
Greddy MSS as a fan controller
Engine/Drivetrain/Engine Bay
1994 VH45DE with ~88k miles; replaced every gasket and seal from the OEM full gasket set except the head gaskets
Many exterior engine parts/brackets replaced or repainted.
Full Mazworx VH45 to S-chassis swap kit including intake and headers
Xcessive Engineering alternator bracket
B14 brake booster (smaller diameter)
Touge Factory SR20 Pulley set (water pump, alternator, PS)
Most visible bolts replaced with SS cap screw or button heads or new OEM.
Nickel plated OEM fuel rails
All new OEM vacuum and breather lines under plenum (All of the complex formed lines if you know the VH45 at all)
Wiring specialties S14-VH45 Pro harness (not installed)
S1 ECU and Nistune Daughter board (not installed)
1991 Z32 TT transmission with ~60k miles with all outer seals/parts refreshed
Z1 Motorsports "Mild Performance" clutch kit
Z1 Motorsports 11 LB flywheel
Z1 Motorsports Short Shifter
Xcessive Engineering shifter bracket
Mazworx/PST aluminum driveshaft
S15 Helical LSD
Sard FPR and gauge
Fuel Lab billet fuel filter
All fuel lines are aeroquip startlite
Billion universal PS reservoir
Earls cooler for PS
All PS lines are aeroquip AQP high pressure
Griffin radiator custom made for me - S14 Chassis with VH45 hose outlets, i'm using both OEM radiator hoses)
FAL S14 bolt on radiator fans
Sard catch can
Generic CF cooling panel
Chassis/Brake/Suspension
R33 GTS-T front Calipers with OEM Nissan rotors
I have the 75% of the stuff for R33/Z32 rear brake swap (not installed)
Z32 rear uprights (not installed)
SPL brake lines
Yashio Factory core support braces
Supernow billet sway bar brackets (for the OEM bars)
Progress Group sway bars (no brackets or endlinks)
Tanabe tension rods with highest spec Aurora rod ends
Nismo power brace
Nismo front/rear strut tower bars (front not installed for the obvious reason)
SPL diff and subframe bushings GEN 1 (not installed)
Last edited:
