TORQUE Specs

Just a Hunter Aug 3, 2019

  1. Just a Hunter

    Just a Hunter Test Drive

    Messages:
    28
    Location:
    Georgia
    Ive referenced this information so many times that I've printed it out and placed it into a folder.

    When in doubt, please confirm the proper torque is chosen for your application by referencing an Xterra service manual.

    Front Suspension:
    Swaybar Mounting Brackets: 96 ft-lbs
    Swaybar Connecting Rod (Both Ends): 62 ft-lbs (Replace After Removal)
    LCA Bump Stop: 14 ft-lbs
    LCA Cam Bolt: 100 ft-lbs
    LCA Ball Joint Nut: 70 ft-lbs (Replace After Removal)
    UCA Mount Bolt: 94 ft-lbs
    UCA Ball Joint Nut: 58 ft-lbs (Replace Cotter Pin After Removal)
    Lower Shock Mount: 155 ft-lbs [
    Upper Shock Mount Nuts: 22 ft-lbs (there are 3 nuts)
    Shock Upper Spring Seat Nut: 30 ft-lbs (Replace After Removal)
    Wheel Hub Mounting Bolts: 44 ft-lbs (there are 4 bolts) (Replace After Removal)
    Center Hub Nut: 101 ft-lbs (Replace Cotter Pin After Removal)


    Rear Suspension:
    Bump Stop: 14 ft-lbs
    Swaybar Mount: 36 ft-lbs
    Swaybar Connecting Rod Nuts: 32 ft-lbs (Replace After Removal)
    Upper Shock Mount Nut: 33 ft-lbs (Replace After Removal)
    Lower Shock Mount: 148 ft-lbs
    Spring Shackle: 77 ft-lbs (Both upper and lower)
    Front Leaf Spring Mount Bolt: 84 ft-lbs (Replace After Removal)
    Axle U-Bolt Nuts: 53 ft-lbs (Replace After Removal)
    Dynamic Dampener (weight): 14 ft-lbs


    Front Diff (R180):
    Diff Mounting Bolts: 135 ft-lbs
    Crossmember Bolts: 96 ft-lbs
    Pinion Nut: 138-216 ft-lbs (Replace After Removal)
    Ring Gear Bolts: 43 ft-lbs
    Carrier Bearing Journal: 69 ft-lbs
    Diff Cover Bolts: 30 ft-lbs


    Rear Diff (C200):
    Pinion Nut: 107-238 ft-lbs (Replace After Removal)
    Ring Gear Bolts: 58 ft-lbs
    Carrier Bearing Journal: 69 ft-lbs
    Axle Bearing/Hub Nuts: 49 ft-lbs ( 4 nuts)
    Diff Cover Bolts: 36 ft-lbs


    Rear Diff (M225 w/o Locker):
    Pinion Nut: 220-500 ft-lbs (Replace After Removal)
    Ring Gear Bolts: 133 ft-lbs (Replace After Removal)
    Carrier Bearing Journal: 80 ft-lbs
    Axle Bearing/Hub Nuts: 89 ft-lbs ( 4 nuts)
    Diff Breather: 31 in-lbs
    Diff Cover Bolts: 31 ft-lbs


    Rear Diff (M225 w/ Locker):
    Pinion Nut: 220-500 ft-lbs (Replace After Removal)
    Ring Gear Bolts: 135 ft-lbs (Replace After Removal)
    Carrier Bearing Journal: 80 ft-lbs
    Axle Bearing/Hub Nuts: 87 ft-lbs (there are 4 nuts)
    Diff Breather: 31 in-lbs
    Locker Wire Harness: 89 in-lbs
    Diff Cover Bolts: 31 ft-lbs


    Front Driveshaft:
    Flange Nut: 44 ft-lbs (Replace After Removal)


    Rear Driveshaft (Model 2S1330):
    Flange Nut: 71 ft-lbs (Replace After Removal)


    Rear Driveshaft (Model 2S1330-BJ100):
    Flange Nut: 41 ft-lbs (Replace After Removal)


    Front Brakes:
    Slide Pin Bolt: 32 ft-lbs
    Torque Member Bolt: 136 ft-lbs
    Union Bolt: 24 ft-lbs
    Bleed Valve: 69 in-lbs


    Rear Brakes:
    Slide Pin Bolt: 19 ft-lbs
    Torque Member Bolt: 76 ft-lbs
    Brake Line: 19 ft-lbs
    Bleed Valve: 69 in-lbs


    Maintenance:
    Engine Oil Drain Plug: 25 ft-lbs (Replace Crush Washer)

    Transfer Case Fill Plug: 26 ft-lbs (Replace Gasket)
    Transfer Case Drain Plug: 26 ft-lbs (Replace Gasket)

    Front Differential Fill Plug: 25 ft-lbs (Replace Gasket)
    Front Differential Drain Plug: 25 ft-lbs (Replace Gasket)

    Rear Differential Fill Plug (C200): 36 ft-lbs (Apply Silicon RTV or Equal)
    Rear Differential Drain Plug (C200): 36 ft-lbs (Replace Gasket)

    Rear Differential Fill Plug (M226) (with or without Locker): 25 ft-lbs (Apply Silicon RTV or Equal)
    Rear Differential Drain Plug (M226) (with or without Locker): 20 ft-lbs (Apply Silicon RTV or Equal)

    Manual Transmission Fill Plug: 25 ft-lbs (Replace Gasket)
    Manual Transmission Drain Plug: 25 ft-lbs (Replace Gasket)

    Automatic Transmission Drain Plug: 25 ft-lbs (Replace Gasket) (both 2wd and 4wd models)

    Engine:
    Intake Manifold: Bolts: First Pass: 5 ft-lb Second Pass: 21 ft-lb
    Intake Manifold: Studs: 8 ft-lb (If removed from Engine Block)
    Intake Manifold: Bolt Pattern: Engine Front: 5, 3, 2, 7
    Intake Manifold: Bolt Pattern: Engine Front: 8, 1, 4, 6

    Misc:
    Wheel Lug Nuts: 98 ft-lbs
     
  2. Prime

    Prime Some Kind of In Charge? Admin

    Messages:
    36,528
    Location:
    Denver-ish
    Stickied. Thank you.
     
    Just a Hunter likes this.
  3. josx2

    josx2 Bought an X Supporting Member

    Messages:
    180
    Location:
    Mebane, NC
    nice TNX salvage :) time to chane my saved bookmark now! thx!
     
    Just a Hunter likes this.

Share This Page