Search results

  1. X

    I don't think I can fix this...

    dang I need an 00 or 01 thanks though sure someone will pick it up
  2. X

    I don't think I can fix this...

    Glad your ok, been thinking of a auto to manual conversion looks like you have all the parts what year is it?
  3. X

    PCV and it's hoses

    If it aint broke dont fix it, sensitive coolant hoses just take off the pcv clean it and see if thats you problem no use creating more, it on the drivers side. Take it by Oreilly or autozone and have it scanned for codes report back View: https://www.youtube.com/watch?v=w6MB7Pd2RyI&t=51s
  4. X

    PCV and it's hoses

    Take it off and clean it
  5. X

    PCV and it's hoses

    cold stuck brake cleaner bath and I bet it fixes it
  6. X

    Anybody have a Calmini kit they can sell me

    Looks like they weld the cups and maybe a urathane type insert? Say's their 'modified' centerlink is not compatable with Moog TRE's because Moogs tend to be a bit bigger and hit the frame, do you have moog? I still have stock but I usually go with moog on all my vehicles.
  7. X

    So This Happened Yesterday.

    oil spreads out in a puddle that is coolant
  8. X

    Anybody have a Calmini kit they can sell me

    I was considering that ac brace although my tires are not that big 31", but for 75$ shipped seems like a necessity. How much was the kit when it was offered ?
  9. X

    Anybody have a Calmini kit they can sell me

    is your idler arm brace sheared off?
  10. X

    Rough idle/stalling at low speed

    No it's above the gas pedal under the dash sits on the hand ebrake on my 2000 Edit Feb 25th Still no stalls running like a champ!
  11. X

    How To Remove Abs System

    I messed up one of my wheel sensors on my 2000 jetta so my abs was coming on all the time, instead of take each off to figure out which one it was, I just removed the ABS fuse; dunno if it would work on the nissan thou. I do not recommend it thou the abs light stays on all the time
  12. X

    Rough idle/stalling at low speed

    Lol stalled again, after all that ! I guess even though the engine was super hot there was not enought time for the Fuel Pump relay to conk out? Anyway I had associated the stalling with the engine warming up it was actually the Fuel Pump relay. At my wit's end I was going to replace the...
  13. X

    Rough idle/stalling at low speed

    And that boys and girls is the end Of this chapter of the story of a 2000 3.3 V6 stalling, you see the sensor was replaced with a brand new crank sensor from Napa made in the USA. And she does not stall anymore, infact she got real hot and did not stall so if you remove the intake remember to...
  14. X

    Rough idle/stalling at low speed

    Well short update, been real cold but much progress! Not getting all those codes any more I grounded the Intake! http://alldatadiy.com/techtips/ALLDATA/20091031.html?affiliate_id=21181&click_id=3853575402&clickId=3853575402 Only code that persists is Knock and Main ignition circuit. Nothing...
  15. X

    02 Nissan Xterra no crank

    Hopefully just one of those large relays on the pass fender, otherwise download the free nissan manual and look at the ignition circuit I'd start with fuses and relays.
  16. X

    02 Nissan Xterra no crank

    – Check the car’s battery voltage. Insufficient battery power can cause sensors to stop reading, triggering a P0600 code. – Visually inspect all sensors and wires. Look for gaps in the insulation, corroded contacts, or severed wires. – Use a multimeter to check all parts of the wiring harness...
  17. X

    Rough idle/stalling at low speed

    Got smart today and disconnected the 4 O2 sensors so I would go full open loop(and i thought stall proof). About 4 miles from home she stalled just as I was relishing in how smart I was. I did get a new code though which points (no pun) to the distributor that was code p1320 ignition signal...
  18. X

    Rough idle/stalling at low speed

    Figured out why it was running rough while testing tbank 1 injectors with a multimeter on automatic OHM. All read 11.4 11.4 11.5. Getting #1 injector connector off was a bitch took about 20 min of careful wiggling and spraying, required spraying wd40 4 times in the clasp mechanism carfully...
  19. X

    Rough idle/stalling at low speed

    I did try unplugging the maf no real difference but I certainly will clean it good with maf cleaner as part of this fix. I have found that the main battery ground is corroded at the battery and has about 4 or 5 different kinds of tape on it on it's way to the Passenger side head, so I will fix...
Top