What have you done for your X?

Muadeeb

Nissan al Gaib
Admin
Location
Dallas
replaced lower ball joints, reattached the sway bar to the frame (was only on the arms) and new meats
balls%20pt2.jpg
 

Muadeeb

Nissan al Gaib
Admin
Location
Dallas
Yeah. The lower ball joints are terrible.
If you mean "Terrible" as in "they suck", then the ones I put in were. If you mean "terrible" as in "hard to replace", not really as a 2wd. Remove the TRE from the knuckle, remove caliper, remove the upper castle nut, loosen the lower, and with a hand holding the knuckle beat the tar out of where the lower ball joint passes through with a bfh. For a 4wd, I'd remove the axle from the diff and work around it. Taking the whole knuckle off makes it a lot easier.
 

rolling rock

First Fill-Up (of many)
Location
PA
Sunday was a syn. oil change & tire rotation & brake check.
Today i get a new drivers side bottom seat cushion due to some tears around the seat controls. (Warranty)

Want the Firestone destinations to last! (love these tires!)
 

Golf286

Wheeling
Location
Niwot, Colorado
Installed the new 5 slot switch panel and finally got the rewiring done for the lights and switches. Still have a lot to get done before goneMoab, new Trans and T-Case are on the way.


image-219807308.jpg
 

rolling rock

First Fill-Up (of many)
Location
PA
Was going to get the seat cushion replaced today.....After taking it down the dealer they called and said "we got the passenger side in by mistake" REALLY? So they reordered the driver side!
 

Madzone26

Test Drive
cleaned engine bay

Cleaned the engine bay! Best I could after flooding it in mud hope to do better next time.
 

Attachments

  • 20150426_192929.jpg
    20150426_192929.jpg
    105.5 KB · Views: 24
  • 20150426_192924.jpg
    20150426_192924.jpg
    104 KB · Views: 28

KChurch86

Banned
Founding Member
Moved my CB Mic, angry monkey, germ grenade, MiniMag and Gerber multi-tool.

More notably, I rebuilt my DIY camp awning. I'll share a pic of that here and put the more detailed photos and info in my build thread.

777c0d570596872dfc9a5aa941764c10.jpg
 

Tay-Lo

I'm the king of junk food!
Location
Upstate SC
Finally got around to putting my bodylift on.....now my tires dont rub the wheel well when I take a turn a little hard. The joy was short lived because I was going down the interstate when the engine decided to over heat.....the top outlet port of the radiator snapped under the added pressure of the hose. I had to stop 3 times over the next 2 miles while I limped home. But I got the radiator replaced this morning.

20150523_091346_zpswdtnfic7.jpg


20150523_133552_zps89n6i5ze.jpg




20150523_091329_Blackedout_zpsv2lwoips.jpg


20150523_133608_Blackedout_zpsi5l7kac9.jpg




20150523_171127_zpsphatupcd.jpg
 

Malin_Rebate

Skid Plates
Location
Tennessee
So I bought a 24 inch pro comp single row lightbar from 4wheelparts. And I basically needed somewhere to put it so I decided on the bumper but had to keep it low profile so this happened

6128dbb90204d9467807db2e4aa1aa77.jpg

fa63759163ed14dc66589751c74287cc.jpg


I also received my "lost" insain fab mounts that were supposed to be here earlier this month

00832519033dcca8cff37e8e029e3c66.jpg

bbff4cc7b29ded12bc757d35bf4f283d.jpg



Sent from my iPhone using Tapatalk
 

USN X

Bought an X
Location
San diego
4x4 parts 3 leaf AAL
Revolver shackles
Bilstein 0-3in shocks front and rear
Upper control arms
4x4 parts TRA
Calmini idler arm brace
Bandit IA bushings
Centric drilled slotted rotors
EBC green stuff pads
Front and rear SS extended brake lines
 

SAKS

Wheeling
Founding Member
Location
Mars
2" body lift
Installed new front bumper
Have new leaf springs sitting in the garage. need to install
Installed a new horn
Wired the new bumper lights to work with the factory fog light switch on the steering column
Wired the wench
Installed new headlight assemblies and got rid of the faded yellow stock ones.
 
Top